電動平板車在使用時會突然出現不能行駛的情況，那么此時該檢測什么呢？

　　檢查升降接觸器總成是否燒壞，線圈是否短路或斷開，維修方法：維修接觸器鉑接觸點或直接更換液壓接觸器總成。

　　檢查升降開關和升降附件電路是否松動或短路，微動開關是否損壞。維修方法：維修和清潔電路，更換或維修微動開關。

　　檢查液壓電機是否有電壓，電機是否短路或開路泄漏，碳刷是否磨損嚴重。維修方法：維修電路，更換電機碳刷，維修電機銅頭，維修液壓電機組件或更換新液壓電機。

　　檢查起重模塊是否燒壞、短路或斷開。修理方法：修理或更換模塊組件。

　　檢查主動電池是否有電壓，如果有電壓，檢查電壓是否能正常使用，維修方法：如果電池沒有電壓或電壓太低，直接給電池充電。

　　電壓過低：電機端電壓比額定電壓低10%以上，電機啟動轉矩過小，使電動平車無法移動和工作。檢查時，用萬用表或電壓表測量電機輸入端電壓。

　　缺相：驅動電機主、控制電路電器損壞、線路斷開或接觸不良，也會使平車驅動電機缺相不能正常工作。在這種情況下，需要對主、控制電路進行維護。維修時，為防止主、控制電路給三相電機的電源缺相，燒毀電機，或驅動電機突然通電，造成危害。首先，將電機從電源線上斷開，只給主、控制電路送電，然后點擊啟動和停止開關，檢查分析控制電器和電路的工作情況，修理或更換有問題的電器或電路。當確認主、控制電路無故障時，可重新試運行。